Eclipse contact times, the magnitude and the duration of totality all ultimately depend on the angular diameters and relative velocities of the Sun and the Moon. Unfortunately, these calculations are limited in accuracy by the departure of the Moon's limb from a perfectly circular figure. The Moon's surface exhibits a rather dramatic topography which manifests itself as an irregular limb when seen in profile. Most eclipse calculations assume some mean lunar radius which averages high mountain peaks and low valleys along the Moon's rugged limb. Such an approximation is acceptable for many applications, but if higher accuracy is needed, the Moon's actual limb profile must be considered. Fortunately, an extensive body of knowledge exists on this subject in the form of Watts' limb charts [Watts, 1963]. These data are the product of a photographic survey of the marginal zone of the Moon and give limb profile heights with respect to an adopted smooth reference surface (or datum). Analyses of lunar occultations of stars by Van Flandern [1970] and Morrison [1979] have shown that the average cross-section of Watts' datum is slightly elliptical rather than circular. Furthermore, the implicit center of the datum (i.e. - the center of figure) is displaced from the Moon's center of mass. In a follow-up analysis of 66000 occultations, Morrison and Appleby [1981] have found that the radius of the datum appears to vary with libration. These variations produce systematic errors in Watts' original limb profile heights which attain 0.4 arc-seconds at some position angles. Thus, corrections to Watts' limb profile data are necessary to ensure that the reference datum is a sphere with its center at the center of mass.

The Watts charts have been digitized by Her Majesty's Nautical Almanac Office in Herstmonceux, England, and transformed to grid-profile format at the U. S. Naval Observatory. In this computer readable form, the Watts limb charts lend themselves to the generation of limb profiles for any lunar libration. Ellipticity and libration corrections may be applied to refer the profile to the Moon's center of mass. Such a profile can then be used to correct eclipse predictions which have been generated using a mean lunar limb.

Along the eclipse path, the Moon's topocentric libration (physical + optical libration) in longitude ranges from l= 0.0 deg to l=-1.6 deg Thus, a limb profile with the appropriate libration is required in any detailed analysis of contact times, central durations, etc.. Nevertheless, a profile with an intermediate libration is valuable for general planning for any point along the path. The center of mass corrected lunar limb profile presented in Figure 6 is for the center line at 12:40 UT. At that time, the Moon's topocentric librations are l=-0.30 deg, b=+0.10 deg and c=+19.65 deg, and the apparent topocentric semi-diameters of the Sun and Moon are 967.4 and 1015.6 arc-seconds respectively. The Moon's angular velocity with respect to the Sun is 0.446 arc-seconds per second.

The radial scale of the profile in Figure 6 (see scale to upper left) is greatly exaggerated so that the true limb's departure from the mean lunar limb is readily apparent. The mean limb with respect to the center of figure of Watts' original data is shown along with the mean limb with respect to the center of mass. Note that all the predictions presented in this paper are calculated with respect to the latter limb unless otherwise noted. Position angles of various lunar features can be read using the protractor in the center of the diagram. The position angles of second and third contact are clearly marked along with the north pole of the Moon's axis of rotation and the observer's zenith at mid-totality. The dashed line arrows identify the points on the limb which define the northern and southern limits of the path. To the upper left of the profile are the Moon's mean lunar radius k (expressed in Earth equatorial radii), topocentric semi-diameter SD and horizontal parallax HP. As discussed in the section MEAN LUNAR RADIUS, the Moon's mean radius k (k=0.2722810) is smaller than the adopted IAU value (k=0.2725076). To the upper right of the profile are the Sun's semi-diameter SUN SD, the angular velocity of the Moon with respect to the Sun VELOC. and the position angle of the path's northern/southern limit axis LIMITS. In the lower right are the Universal Times of the four contacts and maximum eclipse. The geographic coordinates and local circumstances at maximum eclipse are given along the bottom of the figure.

In investigations where accurate contact times are needed, the lunar limb profile can be used to correct the nominal or mean limb predictions. For any given position angle, there will be a high mountain (annular eclipses) or a low valley (total eclipses) in the vicinity which ultimately determines the true instant of contact. The difference, in time, between the Sun's position when tangent to the contact point on the mean limb and tangent to the highest mountain (annular) or lowest valley (total) at actual contact is the desired correction to the predicted contact time. On the exaggerated radial scale of Figure 6, the Sun's limb can be represented as an epicyclic curve which is tangential to the mean lunar limb at the point of contact and departs from the limb by h as follows:

h = S (m-1) (1-cos[C]) [6]

where: S = the Sun's semi-diameter

m = the eclipse magnitude

C = the angle from the point of contact

Herald [1983] has taken advantage of this geometry to develop a graphical procedure for estimating correction times over a range of position angles. Briefly, a displacement curve of the Sun's limb is constructed on a transparent overlay by way of equation [6]. For a given position angle, the solar limb overlay is moved radially from the mean lunar limb contact point until it is tangent to the lowest lunar profile feature in the vicinity. The solar limb's distance d (arc-seconds) from the mean lunar limb is then converted to a time correction Delta by:

Delta = d v cos[X - C] [7]

where: d = the distance of Solar limb from mean lunar limb (arc-sec)

v = the angular velocity of the Moon with respect to the Sun (arc-sec/sec)

X = the center line position angle of the contact

C = the angle from the point of contact

This operation may be used for predicting the formation and location of Baily's beads. When calculations are performed over large range of position angles, a contact time correction curve can then be constructed.

Since the limb profile data are available in digital form, an analytic solution to the problem is possible which is straight forward and quite robust. Curves of corrections to the times of second and third contact for most position angles have been computer generated and are plotted in Figure 6. In interpreting these curves, the circumference of the central protractor functions as the nominal or mean contact time (using the Moon's mean limb) as a function of position angle. The departure of the correction curve from the mean contact time can then be read directly from Figure 6 for any position angle by using the radial scale in the upper right corner (units in seconds of time). Time corrections external to the protractor (most second contact corrections) are added to the mean contact time; time corrections internal to the protractor (all third contact corrections) are subtracted from the mean contact time.

Across all of South America, the Moon's topocentric libration in longitude at maximum eclipse is within 0.2 deg of its value at 12:40 UT. Therefore, the limb profile and contact correction time curves in Figure 6 may be used in all but the most critical investigations.

Next section